Loading...

UCx00 Installation (16)

460 views   March 9, 2019

  • I am getting an “defective plugin” error message when installing the plugin.

    Note that the current published installer uses .Net4.0 which ships with Win10/11.  So make sure you use an up to date version of Win10/11 and the latest version of the installer.  It is common for the browser to try to download an older cac...
    Read more

  • What UCCNC Software version needs to be used with the AXBB-E?

    You need to use UCCNC Development Version 1.2109 or above.  You can download the latest UCCNC software under the Download Attachements for UCCNC or the AXBB-E board. https://www.forum.cncdrive.com/viewtopic.php?f=2&t=240&start=50 &nbsp...
    Read more

  • Can I use the same UCCNC license in multiple computers?

    The UCCNC license is tied to the UC device, so you can install it in as many PCs as you want, but you will only get motion with the PC where the UC device that you registered it tied to.
    Read more

  • Microsoft Defender is seeing a virus in UCCNC or the UC100 Plugin Installer

    Some have reported that Microsoft Defender is seeing a virus in UCCNC or UC100 installers.  We want to assure our users that there is not virus in the software.  This occurs because of the obfuscation method used to protect the software against possible h...
    Read more

  • Is this used for connecting UC-100?

    Yes, it is for the UC100.  Note that this is intended to be used as a replacement, as the UC100 does ship with the cable.
    Read more

  • Tuning UCCNC when using the imperial system

    Some report motion problems with UCCNC which are caused by improper motion settings.  The values found bellow, need to be divided by 25.4.
    Read more

  • will UCCNC work on a mach3 card

    This works only with CNC Drive UC Motion Controllers.  UC100, UC400ETH, UC300ETH. It will work with any breakout board or setup that works with Mach3
    Read more

  • Do I need an additional UC300ETH? Isn't there one built into the C94 itself?

    You have the option of adding it once you hit the "Customize and Add to Cart" button. You can also add DIN Rail Support and Control Software. When you purchase the units together, we ship them assembled.
    Read more

  • Which suggested mounting solutions and suggested power supply (s)?

    The idea is that you power each side of the circuit with the +5vdc that is powering the other side of the circuit.  So for the PC side, you can use a USB cable and for the other side +5vdc from the breakout board.  This circuit requires very little power....
    Read more

  • My UC100 stopped working

    It possible that a spike from the stepper drivers may have damaged the UC100.  Please keep in mind that modern stepper drivers in order to improve performance and generate very high voltage spikes.  It is the high voltage that saturates the driver the coi...
    Read more

  • I installed a uc400eth,using Mach 3. I get estop condition. diagnostic page shows red flashing light for e stop, and solid yellow for all limit.homing switched.

    There are a number of issues that could explain that.  The first thing that comes to mind is: You may not have communication with the board?  Make sure you establish communication using the UCxx Utility software. You may just need to invert ...
    Read more

  • Is the UC300ETH included with the C94?

    Yes, you can choose to add it or not on checkout to give the option to users who already own a UC300ETH to get the board without purchasing a UC300ETH again. If you purchase it as a bundle, it will come with the UC300ETH preinstalled.
    Read more

  • Windows USB Drivers not Working with the UC100

    This is caused by a EU certificate Issue. Try to install these new drivers: http://cncdrive.com/MC/UC100%20files%20for%20manual%20installation/UC100_USB%20drivers.zip Disconnect the computer from the internet. Then in the Windows device manager unins...
    Read more

  • Having problems with the UC device

    Make sure you have Win10/11 up to date before running the current installer. I would recommend downloading the installer using a different browser to avoid having the browser use an older cached download.
    Read more

  • Will the UC300ETH work with Mach4. If not, will it be supported down the road?

    Yes, it works with Mach4. Note that there are some compatibility issues with the current version of Mach4, and an older version is recommended at this time. Please check these instructions which contain a link to the version that is recommended: https:/...
    Read more

  • Problems with the UC100 USB Driver

    The solution described on that link beloow solves the problem when the USB drivers got disabled and were unable to install on Windows 10/11. The issue is basically a Windows security policy issue, it looks to us that Microsoft changed it back and forth in...
    Read more


© 2017 CNC4PC. All Rights Reserved.